|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
TDA7560A 4 x 45 W quad bridge car radio amplifier Feature Superior output power capability: - 4 x 50 W/4 max. - 4 x 45 W/4 EIAJ - 4 x 30 W/4 @ 14.4 V, 1 kHz, 10 % - 4 x 80 W/2 max. - 4 x 77 W/2 EIAJ - 4 x 55 W/2 @ 14.4 V, 1 kHz, 10 % Multipower BCD technology MOSFET output power stage Excellent 2 driving capability Hi-fi class distortion Low output noise Standby function Mute function Automute at min. supply voltage detection Low external component count: - Internally fixed gain (26 dB) - No external compensation - No bootstrap capacitors On board 0.35 A high side driver Flexiwatt27 (vertical) Overrating chip temperature with soft thermal limiter Output DC offset detection Load dump voltage Fortuitous open GND Reversed battery ESD Description The TDA7560A is a breakthrough BCD (Bipolar / CMOS / DMOS) technology class AB audio power amplifier in Flexiwatt 27 package designed for high power car radio. The fully complementary P-Channel/N-Channel output structure allows a rail to rail output voltage swing which, combined with high output current and minimized saturation losses sets new power references in the car-radio field, with unparalleled distortion performances. Protections Output short circuit to GND, to VS, across the load Very inductive loads Device summary Order code E-TDA7560A Table 1. Package Flexiwatt27 (vertical) Packing Tube November 2008 Rev 3 1/15 www.st.com 1 Contents TDA7560A Contents 1 2 Block and pin connection diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.1 2.2 2.3 2.4 2.5 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Standard test and application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.1 3.2 3.3 3.4 3.5 SVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Input stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Standby and muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 DC offset detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Heatsink definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 5 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2/15 TDA7560A List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3/15 List of figure TDA7560A List of figure Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin connection (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Standard test and application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Quiescent current vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Output power vs. supply voltage (RL = 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Output power vs. supply voltage (RL = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Distortion vs. output power (RL = 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Distortion vs. output power (RL = 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Distortion vs. frequency (RL = 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Distortion vs. frequency (RL = 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Crosstalk vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Supply voltage rejection vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Output attenuation vs. supply voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Output noise vs. source resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Power dissipation and efficiency vs. output power (sine-wave operation) . . . . . . . . . . . . . 10 Power dissipation vs. output power (music/speech simulation); RL = 4 x 4. . . . . . . . . . . . .11 Power dissipation vs. output power (music/speech simulation); RL = 4 x 2. . . . . . . . . . . . .11 ITU R-ARM frequency response, weighting filter for transient pop. . . . . . . . . . . . . . . . . . . 11 Flexiwatt27 (vertical) mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . . 13 4/15 TDA7560A Block and pin connection diagrams 1 Block and pin connection diagrams Figure 1. Block diagram Vcc1 Vcc2 470F ST-BY OFF DET MUTE HSD HSD/OFF DET OUT1+ IN1 0.1F OUT1PW-GND OUT2+ IN2 0.1F OUT2PW-GND OUT3+ IN3 0.1F OUT3PW-GND OUT4+ IN4 0.1F AC-GND 0.47F SVR 47F D03AU1467 100nF OUT4PW-GND TAB S-GND Figure 2. Pin connection (top view) 1 27 TAB PW-GND OUT2- ST-BY OUT2+ OUT1- PW-GND OUT1+ SVR IN1 IN2 S-GND IN4 IN3 AC-GND OUT3+ PW-GND OFF DET OUT3- MUTE PW-GND OUT4+ D03AU1468 OUT4- HSD TAB VCC VCC 5/15 Electrical specifications TDA7560A 2 2.1 Electrical specifications Absolute maximum ratings Table 2. Symbol VCC VCC (DC) VCC (pk) IO Ptot Tj Tstg Absolute maximum ratings Parameter Operating supply voltage DC supply voltage Peak supply voltage (for t = 50 ms) Output peak current Repetitive (duty cycle 10 % at f = 10 Hz) Non repetitive (t = 100 s) Power dissipation Tcase = 70 C Junction temperature Storage temperature Value 18 28 50 9 10 85 150 -55 to 150 Unit V V V A A W C C 2.2 Thermal data Table 3. Symbol Rth j-case Thermal data Parameter Thermal resistance junction to case Max. Value 1 Unit C/W 2.3 Table 4. Electrical characteristics Electrical characteristics (Refer to the test and application diagram, VS = 13.2 V; RL = 4 ; Rg = 600 ; f = 1 kHz; Tamb = 25 C; unless otherwise specified). Parameter Quiescent current Output offset voltage During mute ON/OFF output offset voltage Voltage gain Channel gain unbalance VS = 13.2 V; THD = 10 % VS = 13.2 V; THD = 1 % VS = 14.4 V; THD = 10 % VS = 14.4 V; THD = 1 % 23 16 28 20 25 19 30 23 25 26 RL = Play Mode Test condition Min. 80 Typ. 200 Max. 320 50 60 27 1 Unit mA mV mV dB dB Symbol Iq1 VOS dVOS Gv dGv Po Output power W 6/15 TDA7560A Table 4. Electrical specifications Electrical characteristics (continued) (Refer to the test and application diagram, VS = 13.2 V; RL = 4 ; Rg = 600 ; f = 1 kHz; Tamb = 25 C; unless otherwise specified). Parameter Test condition VS = 13.2 V; THD = 10 %, 2 VS = 13.2 V; THD = 1 %, 2 VS = 14.4 V; THD = 10 %, 2 VS = 14.4 V; THD = 1 %, 2 VS = 13.7 V; RL = 4 VS = 13.7 V; RL = 2 VS = 14.4 V; RL = 4 VS = 14.4 V; RL = 2 Po = 4 W Po = 15 W; RL = 2 "A" Weighted Bw = 20 Hz to 20 kHz f = 100 Hz; Vr = 1 Vrms PO = 0.5 W 50 100 80 f = 1 kHz PO = 4 W f = 10 kHz PO = 4 W VST-BY = 1.5V VST-BY = 0 V 60 50 Min. 42 32 50 40 41 43 75 Typ. 45 34 55 43 45 77 50 80 0.006 0.015 35 50 70 300 100 70 60 120 20 10 10 3.5 1.5 80 3.5 1.5 6.5 7 7.5 7 -5 12 8 18 18 A A 90 A V V dB V V 0.02 0.03 50 70 Max. Unit Symbol Po Output power W Po EIAJ Po max. THD eNo SVR fch Ri CT ISB Ipin5 VSB out VSB in AM VM out VM in EIAJ output power(1) Max. output power(1) Distortion Output noise Supply voltage rejection High cut-off frequency Input impedance Cross talk W W % V dB kHz K dB A Standby current consumption ST-BY pin current Standby out threshold voltage Standby in threshold voltage Mute attenuation Mute out threshold voltage Mute in threshold voltage VST-BY = 1.5 V to 3.5 V (Amp: ON) (Amp: OFF) POref = 4W (Amp: Play) (Amp: Mute) (Amp: Mute) Att 80 dB; POref = 4 W (Amp: Play) Att < 0.1 dB; PO = 0.5 W VMUTE = 1.5 V (Sourced current) VMUTE = 3.5 V VAM in VS automute threshold V Ipin23 Muting pin current HSD section VM MAX Vdropout Iprot Mute voltage for HSD operation Dropout voltage Current limits IO = 0.35 A; VS = 9 to 16 V 400 0.25 6 0.6 800 V V mA 7/15 Electrical specifications Table 4. TDA7560A Electrical characteristics (continued) (Refer to the test and application diagram, VS = 13.2 V; RL = 4 ; Rg = 600 ; f = 1 kHz; Tamb = 25 C; unless otherwise specified). Parameter Test condition Min. Typ. Max. Unit Symbol Offset detector (Pin 26) VM_ON VM_OFF VOFF V26_T V26_F Mute voltage for DC offset detection enabled 8 VST-BY = 5 V 2 0 12 3 6 4 1.5 V V V V V Detected differential output offset VST-BY = 5 V; Vmute = 8 V Pin 26 voltage for detection = True Pin 26 voltage for detection = False VST-BY = 5 V; Vmute = 8 V VOFF > 4 V VST-BY = 5 V; Vmute = 8 V VOFF > 2 V 1. Saturated square wave output. 2.4 Standard test and application circuit Figure 3. Standard test and application circuit C8 0.1F C7 2200F Vcc1-2 Vcc3-4 7 21 10 9 OUT1 R1 ST-BY 10K R2 MUTE 47K C1 IN1 0.1F IN2 C2 0.1F IN3 C3 0.1F IN4 C4 0.1F S-GND 15 14 17 C5 0.47F SVR C6 47F 11 16 13 12 C10 1F C9 1F 23 5 8 6 3 4 OUT2 18 19 20 OUT3 22 25 24 26 1, 27 2 OFF DET OUT4 HSD/OFF DET TAB D03AU1469 8/15 TDA7560A Electrical specifications 2.5 Figure 4. Electrical characteristics curves Quiescent current vs. supply voltage Figure 5. Output power vs. supply voltage (RL = 4) 240 220 200 180 160 140 Id (mA) Vi = 0 RL = 4 Ohm 8 10 12 Vs (V) 14 16 18 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 Po (W) Po-max RL= 4 Ohm f= 1 KHz THD= 10 % THD= 1 % 8 9 10 11 12 13 14 Vs (V) 15 16 17 18 Figure 6. Output power vs. supply voltage (RL = 2) Figure 7. Distortion vs. output power (RL = 4) 130 120 110 100 90 80 70 60 50 40 30 20 10 Po (W) Po-max THD (%) 10 Vs= 14.4 V RL = 4 Ohm f = 10 KHz RL= 2 Ohm f= 1 KHz 1 THD= 10 % 0.1 THD= 1 % 0.01 f = 1 KHz 8 9 10 11 12 13 14 Vs (V) 15 16 17 18 0.001 0.1 1 Po (W) 10 Figure 8. Distortion vs. output power (RL = 2) Figure 9. Distortion vs. frequency (RL = 4) 10 THD (%) Vs= 14.4 V 10 THD (%) 1 RL = 2 Ohm f = 10 KHz 1 Vs = 14.4 V RL = 4 Ohm Po = 4 W 0.1 f = 1 KHz 0.1 0.01 0.01 0.001 0.1 1 Po (W) 10 0.001 10 100 f (Hz) 1000 10000 9/15 Electrical specifications TDA7560A Figure 10. Distortion vs. frequency (RL = 2) Figure 11. Crosstalk vs. frequency 10 THD (%) 90 80 CROSSTALK (dB) 1 Vs = 14.4 V RL = 2 Ohm Po = 8 W 70 60 50 RL = 4 Ohm Po = 4 W Rg = 600 Ohm 0.1 40 30 0.01 0.001 10 20 100 f (Hz) 1000 10000 10 100 f (Hz) 1000 10000 Figure 12. Supply voltage rejection vs. frequency SVR (dB) 100 90 80 70 60 50 40 30 20 10 100 f (Hz) 1000 10000 Rg= 600 Ohm Figure 13. Output attenuation vs. supply voltage OUT ATTN (dB) 0 -20 -40 -60 -80 -100 5 6 7 Vs (V) 8 9 10 RL = 4 Ohm Po= 4 W ref. Vripple= 1 Vrms Figure 14. Output noise vs. source resistance Figure 15. Power dissipation and efficiency vs. output power (sine-wave operation) Ptot (W) 90 80 n Vs= 13.2 V RL= 4 x 4 Ohm f= 1 KHz SINE En (uV) 130 120 110 100 90 80 70 60 50 40 30 20 n (%) 90 80 70 60 50 40 Vs= 14.4 V RL= 4 Ohm 70 60 50 40 22-22 KHz lin. 30 20 Ptot 30 20 10 "A" wgtd 10 0 1 10 100 1000 Rg (Ohm) 10000 100000 0 2 4 6 0 8 10 12 14 16 18 20 22 24 26 28 30 Po (W) 10/15 TDA7560A Electrical specifications Figure 16. Power dissipation vs. output power Figure 17. Power dissipation vs. output power (music/speech simulation); (music/speech simulation); RL = 4 x 4 RL = 4 x 2 30 25 20 15 10 5 Ptot (W) Vs= 13.2 V RL= 4 x 4 Ohm GAUSSIAN NOISE CLIP START 60 55 50 45 40 35 30 25 20 15 10 5 Ptot (W) Vs= 13.2 V RL= 4 x 2 Ohm GAUSSIAN NOISE CLIP START 0 1 2 3 Po (W) 4 5 6 0 2 4 Po (W) 6 8 10 Figure 18. ITU R-ARM frequency response, weighting filter for transient pop Output attenuation (dB) 10 0 -10 -20 -30 -40 -50 10 100 1000 Hz 10000 100000 AC00343 11/15 Application hints TDA7560A 3 Application hints (ref. to the circuit of Figure 3) 3.1 SVR Besides its contribution to the ripple rejection, the SVR capacitor governs the turn ON/OFF time sequence and, consequently, plays an essential role in the pop optimization during ON/OFF transients.To conveniently serve both needs, ITS MINIMUM RECOMMENDED VALUE IS 10 F. 3.2 Input stage The TDA7560A's inputs are ground-compatible and can stand very high input signals (8 Vpk) without any performances degradation. If the standard value for the input capacitors (0.1F) is adopted, the low frequency cut-off will amount to 16 Hz. 3.3 Standby and muting Standby and Muting facilities are both CMOS-compatible. In absence of true CMOS ports or microprocessors, a direct connection to Vs of these two pins is admissible but a 470 kOhm equivalent resistance should be present between the power supply and the muting and ST-BY pins. R-C cells have always to be used in order to smooth down the transitions for preventing any audible transient noises. About the standby, the time constant to be assigned in order to obtain a virtually pop-free transition has to be slower than 2.5 V/ms. 3.4 DC offset detector The TDA7560A integrates a DC offset detector to avoid that an anomalous DC offset on the inputs of the amplifier may be multiplied by the gain and result in a dangerous large offset on the outputs which may lead to speakers damage for overheating. The feature is enabled by the MUTE pin (according to Table 4) and works with the amplifier unmuted and with no signal on the inputs. The DC offset detection can be available at 2 different pins: - - Pin 2 (always enabled) Pin 26. Only enabled if Vmute (pin23) is set higher than 8V. If not (Vmute < 6 V) pin 26 will revert to the original HSD function 3.5 Heatsink definition Under normal usage (4 Ohm speakers) the heatsink's thermal requirements have to be deduced from Figure 16, which reports the simulated power dissipation when real music/speech programmes are played out. Noise with gaussian-distributed amplitude was employed for this simulation. Based on that, frequent clipping occurrence (worst-case) will cause Pdiss = 26 W. Assuming Tamb = 70 C and TCHIP = 150 C as boundary conditions, the heatsink's thermal resistance should be approximately 2 C/W. This would avoid any thermal shutdown occurrence even after long-term and full-volume operation 12/15 TDA7560A Package information 4 Package information In order to meet environmental requirements, ST (also) offers these devices in ECOPACK(R) packages. ECOPACK(R) packages are lead-free. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Figure 19. Flexiwatt27 (vertical) mechanical data and package dimensions DIM. A B C D E F (1) G G1 H (2) H1 H2 H3 L (2) L1 L2 (2) L3 L4 L5 M M1 N O R R1 R2 R3 R4 V V1 V2 V3 MIN. 4.45 1.80 0.75 0.37 0.80 25.75 28.90 mm TYP. 4.50 1.90 1.40 0.90 0.39 1.00 26.00 29.23 17.00 12.80 0.80 22.47 18.97 15.70 7.85 5 3.5 4.00 4.00 2.20 2 1.70 0.5 0.3 1.25 0.50 MAX. 4.65 2.00 1.05 0.42 0.57 1.20 26.25 29.30 MIN. 0.175 0.070 0.029 0.014 0.031 1.014 1.139 inch TYP. 0.177 0.074 0.055 0.035 0.015 0.040 1.023 1.150 0.669 0.503 0.031 0.884 0.747 0.618 0.309 0.197 0.138 0.157 0.157 0.086 0.079 0.067 0.02 0.12 0.049 0.019 MAX. 0.183 0.079 0.041 0.016 0.022 0.047 1.033 1.153 OUTLINE AND MECHANICAL DATA 22.07 18.57 15.50 7.70 22.87 19.37 15.90 7.95 0.869 0.731 0.610 0.303 0.904 0.762 0.626 0.313 3.70 3.60 4.30 4.40 0.145 0.142 0.169 0.173 5 (Typ.) 3 (Typ.) 20 (Typ.) 45 (Typ.) Flexiwatt27 (vertical) (1): dam-bar protusion not included (2): molding protusion included V C B V H H1 H3 H2 R3 R4 V1 R2 R L L1 A V3 L4 O L2 N L3 V1 V2 R2 L5 G G1 F R1 R1 R1 E FLEX27ME D Pin 1 M M1 7139011 13/15 Revision history TDA7560A 5 Revision history Table 5. Date 16-Mar-2003 Document revision history Revision 1 Initial release. Document reformatted. Changed the order code, see Table 1: Device summary. Updated Table 4: Electrical characteristics. Added Figure 18: ITU R-ARM frequency response, weighting filter for transient pop. Modified max. values of the VOS and THD parameter in Table 4: Electrical characteristics. Changes 29-Sep-2008 2 07-Nov-2008 3 14/15 TDA7560A Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 15/15 |
Price & Availability of TDA7560A |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |